For hosts, MCs and event producers
Teleprompter for event host
A teleprompter for event host is the way to read a wedding, gala or awards script without losing your place in front of a full room. The words scroll at the pace you speak, so you keep your eyes on the audience instead of on a printed page. A prompter also lets you jump straight to the next block of the run of show, which matters when every speech has to fit a fixed programme. It runs in the browser, needs no account and no installation, and the script stays on your own device. Use it with a countdown and a Bluetooth remote so you can drive it from the stage without walking back to the laptop.
Why an event host reads from a teleprompter
An event script is not a speech, it is a schedule. A gala of two hours can hold an opening, six awards, three speeches and a closing, and every one of those blocks has a slot that was fixed months ago. The host has to know which block comes next, how long it lasts and what has to be said before it starts. Reading that from a stack of printed pages in front of 300 people is where events go wrong.
A prompter turns the run of show into one scrolling document. Each block is a paragraph, so the host can jump to the next one without searching for it. The word count and the reading time shown next to the editor let you check the length of a block before the event, and the countdown gives you the seconds before the first word.
- You stop turning paper over in front of the audience.
- You never lose your place, because the words scroll at your pace.
- You can step to the block that is happening now and come back afterwards.
- You read the names and the figures at a slower speed than the rest.
- The script stays on your own device, which matters for a private event.
The prompter does not record the event, it does not play music and it does not mix sound. It shows the words, the production stays where it is.
Running the show with a teleprompter for event host
Timing is the whole job of a host, and it is decided by the programme, not by the script. You know the block before the next one has to fit into a 4 minute slot, and you know the awards have to be read while the winner walks to the stage. A prompter makes that visible, because the length of every block is on the screen next to the text.
Write one block per paragraph and mark the cue at the top of it, so the host always knows what the block is for: 'Award 1', 'Sponsor thanks', 'Closing'. When the evening runs late, you shorten a block and the prompter shows exactly which words you removed.
- One block per paragraph: opening, award, speeches, closing.
- Check the word count of each block against its slot in the programme.
- Read the names and the figures at 110 words per minute, the rest at 140.
- Keep the cue for each block in its first line, so you never wonder what is next.
- Mark a pause before an award with [PAUSE], it keeps the room calm.
Jumping between blocks without losing your place
The useful part of a prompter at a live event is not the scroll, it is the jump. The host does not read from the top, because the order of the evening depends on what happens in the room. The left and right arrows move from one paragraph to the next, so you can step to the award that is being handed out and return afterwards.
That only works if each block stands on its own. A block that opens with 'as I mentioned earlier' cannot be read in the middle of the evening, because the earlier part was in another paragraph. Write blocks that make sense read cold, with the context repeated in one short line at the top.
- Use the left and right arrows to move between blocks.
- Use R to go back to the top when the order of the evening changes.
- Keep the closing block last in the file, so it is the last thing you can reach.
- Give every block a first line that says what it is, in under 10 words.
- Keep the awards in the order of the categories, not in the order you remember them.
Teleprompter or printed cue card
A printed cue card is a valid tool. For a 60 second thank you to a retiring colleague, a card on a lectern is enough and nobody notices it. The prompter earns its place when the script is longer than a card can hold, when the order changes during the evening, or when the wording has to be exactly right.
- A card holds 3 or 4 lines; a prompter holds a whole block of 100 words or more.
- Turning a card over by hand takes 2 seconds and shows in the room.
- A prompter jumps between blocks with a key press, with nothing visible.
- A card is fine for one short speech, a prompter is for a running show.
- A prompter adds a countdown and remote control, a card has neither.
If you are still nervous about reading on camera, read the block 3 times before the event. The words stop being new on the third pass, which is what makes the delivery sound easy.
Getting names, figures and sponsors right
The mistakes people remember at an event are the names and the numbers: the surname of the award winner, the number of years the company has been running, the amount of the donation, the name of the sponsor. Reading those from a card is the classic mistake, because you glance down and you guess.
Put every name and every figure in its own paragraph, so you can read that part slowly and read the rest at the pace of the room. At 110 words per minute the names land properly. If a name is hard to pronounce, write it phonetically in brackets, exactly as it should be said out loud.
- Check the spelling of every name against the list the organiser sent you.
- Write hard names phonetically: 'Nguyen (win)'.
- Read the figures at 110 words per minute and the rest at 140.
- Keep the sponsor names in the order they appear on screen.
- Check the totals once more the day before, prices change.
Countdown, remote and keyboard control from the stage
On stage you are not standing at the laptop. The prompter is on a screen at the front of the room and you are holding a microphone, so the controls need to be somewhere else. The countdown handles the run up: choose 0, 3, 5 or 10 seconds and the scroll starts on its own when the number reaches zero.
A Bluetooth controller or a presentation remote sends the same keys as the keyboard. The south button plays and pauses, and the directional pad changes the speed and jumps between paragraphs. That is enough to run a block, hold for a reaction and move on, without leaving the stage.
| Control from the stage | What it does |
|---|---|
| Space or the play button | Start or pause the scroll |
| Up / Down arrows | Slower or faster, 5 words per minute at a time |
| Left / Right arrows | Previous or next block |
| R | Back to the top of the script |
| Bluetooth controller | The same keys as the keyboard |
| Presentation remote | Sends the arrow keys |
Test the remote before the doors open. The prompter has to be on the second screen or on a tablet, and the laptop has to be plugged in, because the scroll must not stop halfway through the awards.
References and tools
Official documentation, for the recording side and for the general idea of a prompter.
Frequently asked questions
How do I use a teleprompter at a wedding reception?
What is the difference between a teleprompter and a cue card?
How fast should I read an event script?
Can I control the prompter from the stage?
Is my event script uploaded anywhere?
Open the teleprompter for your next event
Open the teleprompter, paste your run of show and press start. The words scroll at the pace you speak, the countdown and the Bluetooth remote keep you on time, and nothing is uploaded.
Open the teleprompter